Cabinet Lighting–: Putting in beneath cabinet lighting?
I want to add beneath-cabinet lighting to my kitchen. We want to use xenon/halogen strips below every single of four cabinets and we wanna wire them this kind of that no wires show and a light switch will turn them on/off.
Is this one thing that an amateur can do? If we hired an electricitian, how a lot would this cost (ballpark figure)?
picture of kitchen: nttp://img432.imageshack.us/img432/8820/kitchensizedae1.jpg
u can see the four cabinets there that we wanna put the lights underneath
to left of sink (behind paper towels) is a light switch to control garbage disposal and then an electrical outlet i was considering we could tap into that electrical outlet’s energy and install a light switch more than there to energy all of the lights.
we wanna go permanent as component of our kitchen upgrading we painted the kitchen right now and are crown moulding this weekend then we are gonna tile the backsplash, so i am thinking we should do the undercabinet wiring first, or at least program for it before we tile the location…
all outlets in kitchen are GFCI
The answer in the following: (Hint: For answers, no site audit.)
Answer by Mindwalk8
I like what you are preparing to do.. One thing to believe about for now..
Costco sells these little stick on push and click lights.. three AA batteries run the Led’s.. and despite the fact that they are a bit spotlight ish.. you can get an concept of what it will be like.. and there is absolultly no require for drilling holes or creating changes to install them.
** Led Light ** are white lights.. and not the yellowish color widespread to tungsten lighting..
We do not use our kitchen really often and when we are.. the sun lights it up so we have not had a need to have to turn on the lights.. Batteries perform actually nicely for us..
Very good luck!
Answer by myke_cyndy
k ahead of you commence you will need to modify the outlet to a GFCI by the sink code requires you to have 1 by in which every single there is water also you need to check the amp rating on the breaker to see if it can handel it and yes you can do just make a list of factor you r going to want and go to a home improvent store like lowes or house depot and show and then clarify to them and they will aid you
Solution by imaquitter
Yes, you can do this. Go to House Depot and they sell Xenon below counter lighting there.
You have a beautiful kitchen…
Answer by frank m
I can tell you this is not something you want to do by oneself in you kitchen. At times you just gotta know when to leave it to someone who is aware of. The N.E.C. states that lighting are not able to be a portion of the small appliance circuits. To be code compliant and protected you have to get this performed right and a residential electrician is the correct choice for the occupation. The initial issue to do is find a journeyman residential electrician. Ask pals, builders or visit spots exactly where houses are staying developed and speak to them. Describe what you have in mind and offer you them adequate to make it really worth their time to do it appropriate. It could turn into a six hour task to do this and I would gladly pay $ 300 to have it performed proper. This may possibly sound like a lot of income and it is for some, but a great residential electrician can keep away from damage to the walls, tiles, countertops, and cabinets and save very high-priced and time consuming repairs. It will also get completed correct so that when it really is time to market you don’t have to fail a home inspection because of a code violation and the expenditures of correcting the violations. This is possibly not what you wanted to hear but it truely is the ideal suggestions. Excellent luck.
Answer by JeffeVerde
Definitely get the wiring in the walls before you do Anything at all else in the kitchen – at ideal, additional work will interfere with the wiring – at worst, you could finish up acquiring to tear stuff out that you just put in, to get into the wall.
If you want puck lights (and by the way, pay the extra $ 4/bulb for Xenon – they burn considerably cooler than Halogens do), you’ll have a remote transfomer to step the 120v down the the 12v the lights demands. HomeDepot/Lowes have puck light kits comprehensive with the transformer. If the lead from the pucks to the transformer is long sufficient, the easiest factor would be to put the transformer up on prime of the cabinets. The transformer plugs into a receptacle, so I’d just wire a receptacle at the top of every cabinet. I assume when you say crown, you’re talking about on best of the upper cabinets? If so, everything will be hidden by the molding.
Seeking at your picture, I’d place two pucks below every of the single cabinets, and four or five underneath the corner cabinet. The light kits come in one, three, and 5 light kits (you do not have to use all the lights). I’d put a receptacle close to the corner to cover all the lights in that row of cabinets, and a 2nd over the single cabinet to the proper of the sink.
Considering that you are going to be putting a backsplash in, I’d open the drywall over the counters to run the wiring. Cut a hole above the cabinets for an “old operate box”, and fish down the wall to pull the romex up. For esthetics, I would place the switch for the undercabinet lights in the very same junction box as the garbage disposal, making a 2-gang switch, rather than two singles near each other. In your case this is going to imply opening the wall and ripping out the existing single gang box. But you’re going to cover it all with backsplash anyway, so no worries.
On the topic of the kitchen tiny-appliance circuit and undercabinet lights– this is always a exciting 1 in the electrician discussion boards. Ideal to play it safe and power these receptacles off a general lighting and receptacles circuit. If you don’t have simple access to a circuit on the other side of the wall, you can tap into the refrigerator outlet (the fridge is supposed to on 15A branch circuit seperate from the tiny appliance circuits).
Lastly, to Myke_Cyndy — Time for new glasses, Myke. The “GFCI protected gadget” stickers are clearly visible on all of the receptacles in the picture. As for “examine(ing) the amp rating on the breaker to see if it can manage it”. What is to examine? It really is a kitchen countertop modest appliance circuit — by code, it is 20A.
What do you think? Answer under!
Cabinet Lighting
_______________________
The following not about – Cabinet Lighting,but traditional:A burden of one’s choice is not felt.A friend is in no way known till a man has need. Self-confidence in oneself is the very first step on the road to achievement..car maintenance prices。！Remind of festial: New Year’s Day (1/1).
Stunning:
Asian Antique Buffet Cabinet_an1008y
Image by Silk Road Collection
A rare locate, circa 1830, 4 door, four drawer antique Chinese cabinet. Crafted in the Shanxi region of China, this cabinet delivers easy design, beautiful design and generous storage, with straightforward carving in which the legs meet the physique of the cabinet. The light-brown finish reveals the beauty of the walnut wood. Brass pulls adorn the doors and drawers. Could be used as a bathroom vanity-just spot a water vessel on best of the cabinet area or insert into the surface. Pipes are hidden inside of the cabinet.
www.silkroadcollection.com/an1008y-antique-asian-buffet-c…
___________________
You might also like
 |
|
|
|